Aerocool P7 H1 Rgb Led Controller

Aerocool has sent for Aerocool P7 H1 Review. Project 7 is the Aerocool'due south branding for their RGB Gaming line upward of enthusiast level products ranging from PSU to Fan to the Chassis. Today, nosotros will look at their Aerocool P7 H1 Review. This is their controller hub solution to sync and integrate all of their RGB products much like NZXT Hue+ and Corsair Lighting Node Pro/Commander Pro.

Aerocool P7-H1 RGB Controller Hub Review

The P7-H1 is a 5 port Fan hub with two RGB ports for connecting RGB Fans, RGB LED Strips, RGB PSUs, and Chassis. This approach would provide the user to command all of Aerocool'due south RGB products using a simple software control with this hub.

Production: Aerocool P7 H1 Review
Manufacturer: Aerocool
Brand: Project vii
Category: Accessories
Cost: Bank check Price on Amazon

Related: Aerocool P7-L240 CPU Cooler Review

P7-H1 Specifications

Aerocool P7 H1 RGB Packaging and Unboxing

The product is shipped in a black color paper-thin box. There are an Aerocool brand name and logo printed on the top left on the front side. Project seven is printed in the center with the slogan of Exploring the Unknown. P7-H1 is printed in the middle lesser. The behind of the box has Aerocool make proper noun and logo printed on the top left side. P7-H1 is printed on the superlative right side. In that location is a cake diagram of the hub on the peak which is labeled.

Labels info is printed in a pictorial format on the right side. Specifications of the controller hub are printed in the middle section including the contents of the box. Salient features of the hub are printed in 12 dissimilar languages on the left and right sides of the box with each side having six languages printout. Mentioned features are Sync all Aerocool RGB Products, LED output supports upwardly to 24 Watts, Controls up to 5 fans.

The bottom side of the box has a serial no sticker printed on the correct side. Website address of the company is printed on the correct side. Compliance information to various specifications is printed on the left side. The lesser side has a transparent seal on it. The height side where the box is to be opened has a seal on the left and the right side.

Aerocool Accessories and Content

Aerocool has provided following accessories in the box:

1x Velcro Strap
4x screws
4x black Cypher Ties
User Guide

Aerocool Accessories and Content

P7-H1 Closer Expect

The Aerocool P7 H1 Review is a controller hub, designed to integrate/sync all the RGB products from the Aerocool particularly from their Project 7 serial of the products. This allows the user to sync all lighting consequence on all of the Aerocool products at paw to create i heck of a stunning lighting show. Their Projection vii series chassis, Power Supplies, and Coolers can be integrated into this hub for this purpose. Aerocool has provided a software S1 for this hub which allows the users to command the lighting effects and monitor the fan speeds. Let's take a closer await at the hub.

There are Aerocool brand proper noun and logo embossed in the eye on the pinnacle side of the hub. The hub has a dimension of 88mm X 69mm X 17mm. The bottom side of the hub has a plain surface mounted with 4 screws. At that place are cutouts in a group of ii at equal distance from the border. The provided Velcro strap is to be pasted between these cutouts. Iii cables are coming out of the hub from its front end side.

These are 2-pin Molex/Peripheral connector, ix-pin USB 2.0 connector, and 4-pin PWM connector. There is a dip switch with three buttons labeled 123. In that location is a text On with a line next to it indicating the corresponding active hub. The P7-H1 has the functionality of connecting multiple hubs (upwardly to 8) with each other. This switch will be used to actuate the hub(s).

Beneath picture will be helpful in determining the order of the switch in case more than one hubs are to exist used. If you are using only one hub so go out information technology at its manufactory default position. Length of each cable is approximately 480mm without the connector.

usb rgb controller Help

In that location are two 4-pin RGB LED ports on the right side of the hub. These are following the specification of 12V GRB in 5050 format. Hence, this hub is compatible with the majority of the RGB LED headers on the today's motherboards. Full LED output on these two ports is 24 Watts. One tin can daisy chain the LED strips/Fans for connectivity with the hub which would allow using multiple RGB LED enabled devices on a single port but within 24 Watts output.

There are iii iv-pin headers for the fan on the backside of the hub and two on the left side of the hub. Fan output is upwardly to 18 Watts. Please, notation that you tin can't control the speed of the fan(s) using the software S1 but can only monitor the RPM of the fan(south). Beneath diagram will bear witness the connectivity options for understanding purpose.

usb rgb controller Socket Structure

Aerocool has sent the states their P7-L240 Liquid cooler which has 2 P7-F12 RGB fans in it. This gives us the opportunity to test the hub earlier testing the P7-L240 cooler. Each fan has two cables coming out of information technology. 1 is the iv-pin PWM connector cable to power the fan and the other is the RGB LED cable with two connectors.

Ane connector is the extension one to connect ane more RGB LED device, preferably some other P7-F12 fan to daisy chain them. The second connector is the RGB LED header which would plug in the hub or directly on the motherboard's RGB LED header like Asus Aura Sync header for instance.

To exam the Hub, we daisy chained both fans and connect one fan's RGB LED header to the hub. PWM connectors of both fans were connected to the Fan 1 and Fan 2 ports respectively. Please, note that it is not mandatory to connect the PWM connectors to the hub to power upward the fans. The USB ii.0 connector was attached to the Asus Rampage V Edition 10 USB 2.0 header and Molex connector was connected to the PSU.

The software can be downloaded from the Aerocool'southward website to command and monitor the LED lighting and fans' speed. Software installation will not start unless the hub is connected to the motherboard and powered up. Hither are few pictures of the connectivity of this hub with the motherboard.

Software

Let's take a look at the S1 software provided by the Aerocool to be used with the Aerocool P7 H1 Hub Review. The software has a simple and user-friendly interface and allows the user to customize the lighting effect using 16.8 Million colors. On the superlative panel, there are tabs with Hub 1, Hub ii and then on written on them. The software will prove the currently activated hub and its respective options. In that location is a Settings button on the peak right side before the minimize and shut buttons. Information technology has just i option to update the software. There is LED Mode on the top left side with a drib-down box. The modes are:

Breathing
Pulsating
Always on
Off

Limited modes are available at the moment using the software. There are ii more knob style buttons with the slider on them. 1 is to control the brightness of the light and the other is to control the speed of the light effect. The user volition accept to click on the Preview Arrangement button on the right side. This is strange implementation every bit the discussion Preview itself is confusing.

There should be Apply button to make information technology more convenient for the user. One may take the word Preview in its literal meaning of just checking the corresponding outcome without applying information technology whereas this push is really acting like Apply button. On the bottom left side, at that place are five fan icons which light up in the blue to bear witness the continued fan(due south). In our instance, the offset ii icons light up indicating that only ii fans are continued at the moment.

Click on each fan to check its speed in RPM. The software does not have any feature to control the speed of the fans, which would have been an added functionality. The user will have to rely on other methods of speed regulation like using motherboard's BIOS to command and set up the PWM fan curve or using some software for this purpose. In that location are two circles on the tiptop correct side indicating the color range that the user can change to command the lighting color.

The outer circle is to control the color'due south shade whereas the inner circle is to command and set the selected colour. Alternatively, the user can employ the R G B text boxes located beneath the circles past giving colour numbers from o to 256 in each of the boxes. The user can also input the HTML colour lawmaking in the text box below the RGB text boxes. Alternatively, there is a color pallet on the right side of the HTML code textbox which the user can utilise to click and select the color. The user can disengage the last modify too.

Finally, there is a Loop RGB option that tin can be toggled betwixt on and off. By default it is off. Turn it on if you wish to colour the cycles. Please, annotation that there is no Rainbow mode available indicating that the RGB LEDs are non addressable. The user can modify the language of the software at the bottom correct side. Help would take you lot to the web browser with a link to a youtube video demo of the P7-H1. The user can besides sync all the continued hubs in the software.

Determination

The Aerocool P7 H1 Review is an RGB LED Controller Hub, designed to integrate/sync all the RGB products from the Aerocool particularly from their Projection 7 series of the products. This allows the user to sync all lighting effect on all of the Aerocool products at hand to create one heck of a stunning lighting testify. Their Project vii series chassis, Powe, Supplies, and Coolers can be integrated into this hub for this purpose.

The hub has a dimension of 88mm X 69mm Ten 17mm. ii-pin Molex/Peripheral connector, 9-pivot USB 2.0 connector, and four-pivot PWM connector cables are pre-installed on the hub. There is a dip switch with iii buttons labeled 123. The user tin can connect multiple hubs (up to 8) with each other and this switch is used to actuate the corresponding hub. Length of each cablevision is approximately 480mm without connector.

There are ii four-pin RGB LED ports on the hub. These are following the specifications of 12V GRB in 5050 format. Hence, this hub is compatible with majority of the RGB LED headers on the today'south motherboards. Full LED output on these two ports is 24 Watts. One can daisy chain the LED strips/Fans for connectivity with the hub which would allow to utilise multiple RGB LED enabled devices on a unmarried port just within 24 Watts output.

There are total five 4-pivot fan headers on this hub. Fan output is upwards to 18 Watts. Please, annotation that y'all can't control the speed of the fan(due south) using the software S1 only can merely monitor the RPM of the fan(southward). The just Con that I could think of this hub is the majority of cables to deal with but and then again tell me which RGB Controller Hub does not have that issue.

The software to be used with this hub has a simple and user friendly interface except that there is no Apply push to make the changes active and salvage them simply there is a Preview System button which is located in the center of Color Range circle which is rather confusing. The Preview System button has the functionality of Apply button. We are thankful to Aerocool for giving usa the opportunity to review their P7-H1.

Cheque Toll on Amazon

Tech4Gamers Recommended Award

Was our article helpful? 👨‍💻

Thank you! Delight share your positive feedback. 🔋

How could we improve this post? Delight Help united states. 😔